Axxess Interface OESWC LAN11 RF User Manual

INSTALLATION INSTRUCTIONS FOR PART OESWC-LAN11-RF  
OESWC-LAN11-RF  
The OESWC-LAN11-RF is designed to allow you to add steering  
wheel control options to 2006 and up GM LAN11 vehicles. The RF  
controlled OESWC-LAN11-RF will allow the customer to adjust their  
radio without taking their eyes off the road. The OESWC-LAN11-RF  
will come preprogrammed with your most popular features, volume up,  
volume down, seek up, seek down, and source. But with the option of  
remapping the buttons to fit every customer needs, this makes this a  
must have interfaces that the Axxess line offers.  
INTERFACE COMPONENTS  
• A) OESWC Transmitter • B) OESWC Interface • C) Center Keypad  
• D) Trim Ring • E) Strap Cover • F) Vehicle T-Harness  
A
B
C
D
F
E
TOOLS REQUIRED FOR INSTALLATION  
•Cutting Tool Tape •Crimping Tool  
•Connectors (I.E. butt-connectors, bell caps, ECT…)  
1-800-221-0932  
axxessinterface.com  
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION  
Wiring The OESWC Interface  
1. Connect the red wire to 12 volt accessory  
2. Connect the Black wire to ground (you may use the same ground that  
you use for the aftermarket radio)  
Setting Up The OESWC Transmitter  
1. Press the Red and Green buttons simultaneously for 5 seconds, and  
then press volume up for two seconds. This will orientate your button  
direction.  
2. Turn on the ignition and press volume up on the OESWC transmitter.  
This will “marry“ the transmitter to the interface.  
NOTE: If you are replacing a transmitter you must turn on the ignition  
and within the first 10 seconds press and hold the source button for ten  
seconds. This will “marry the new transmitter.  
Programming The OESWC Transmitter  
1. Complete connections to the factory radio  
* If this is the first time the OESWC TRANSMITTER is being installed in a  
vehicle:  
2. Turn the ignition on; the led will start flashing rapidly which means the  
OESWC interface is looking for the vehicle. Go to step 4.  
Or  
* If the OESWC TRANSMITTER was installed in a vehicle before:  
2. Turn the ignition on, the led will flash once.  
3. Hold down the reset button for more then 2 seconds but less then 10  
seconds, the led will start flashing rapidly  
4. After a couple of seconds the led should stop flashing and not light up  
2
for 2 seconds.  
5. This is the end of the auto detection stage. If the OESWC  
TRANSMITTER detected the vehicles radio successfully the led will  
light up solid red.  
6. Make sure the steering wheel control buttons function correctly in the  
vehicle and enjoy your radio.  
So what if the led does not light up solid red? Check out troubleshooting  
section below.  
Troubleshooting the Auto Detect Mode  
So you tried the auto detect feature and at the end the led did not stay on  
solid red, it started flashing. That means the OESWC TRANSMITTER did  
not detect the vehicles radio. Follow these couple steps to determine what  
happened:  
First some basic steps:  
1. Verify that you have 12 volt accessory and a good ground to the  
OESWC interface.  
2. Verify that the battery is good on the OESWC transmitter.  
3. Refer to the “Setting up the OESWC transmitter” section of this  
manual and repeat those steps.  
3
NOTES  
NOTES  
NOTES  
INSTALLATION INSTRUCTIONS FOR PART OESWC-LAN11-RF  
KNOWLEDGE IS POWER  
Enhance your installation and fabrication skills by  
enrolling in the most recognized and respected  
mobile electronics school in our industry.  
800-354-6782 for more information and take steps  
toward a better tomorrow.  
Metra recommends MECP certified  
technicians  
1-800-221-0932  
axxessinterface.com  
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION  

Hobart Corp Convection Oven HBA2E User Manual
Hobart Corp Convection Oven HBA1G User Manual
Hobart CG731 User Manual
Haier HTR20 User Manual
EVGA 113 M2 E113 User Manual
Eizo FlexScan L578 User Manual 1
Clarity C4205 User Manual
BT DIVERSE X10 User Manual
AT T 1465 User Manual
Acura Embedded AcuTouch 150 User Manual